24-hour emergency line, 7 days a week 4.9 from 78 Google reviews
Engineer repairing a boiler with the casing off
Boiler faults

No hot water but the heating works? Here is what is going on

Heating fine but the taps run cold, or the other way round? The diverter valve, motorised valve, cylinder thermostat and plate heat exchanger explained, with what to check first.

  • Written by our engineers
  • Published 3 November 2026
  • Our own published prices

One of the most common calls we get: the radiators are warm, the boiler is running, and the shower is freezing. Or the reverse, lovely hot water and stone-cold radiators. The good news is that this pattern almost always points to one specific part, and it is nearly always a repair rather than a new boiler. Here is how to narrow it down before you call.

First, which type of system do you have?

If there is no hot water cylinder in an airing cupboard, you have a combi, which heats water on demand. If there is a cylinder, you have a system or regular boiler, and the hot water is stored. The fault list is different for each, so start there.

Combi boiler: heating works, no hot water

  • Diverter valve. Inside a combi, a diverter valve switches the boiler between heating the radiators and heating the tap water. When it sticks, you get one but not the other, and sometimes lukewarm water that fades. This is the number one cause on combis over six years old, and it is a parts-and-labour repair, usually done on the first visit.
  • Plate heat exchanger. This small block of plates transfers heat to the tap water. In Essex hard water it scales up, and the symptom is water that starts hot and goes tepid, or a boiler that fires briefly then stops. It can be descaled or replaced.
  • Flow sensor or turbine. If the boiler does not fire at all when you open a hot tap, it may not be seeing the flow. Try a different tap first; if none works, the sensor is likely.
  • Low mains pressure. If the cold tap in the kitchen is also weak, the problem is the supply rather than the boiler. Check with neighbours and the water company.

Combi boiler: hot water works, no heating

Check the obvious first: the programmer or app is set to on, the room thermostat is turned above room temperature, and the wireless thermostat has fresh batteries. Flat thermostat batteries cause more no-heating calls in November than any boiler part. If all that is fine, the diverter valve is again the likely culprit, stuck the other way.

System or regular boiler with a cylinder

  • Motorised valve. A two-port or three-port valve directs hot water either to the radiators or to the cylinder coil. When the motor or the microswitch fails, one circuit never gets heat. You can sometimes hear it buzzing or find the manual lever stiff.
  • Cylinder thermostat. A strap-on thermostat halfway up the cylinder tells the boiler when the water is hot enough. If it fails closed you get no hot water; if it fails open the cylinder overheats and the boiler runs constantly.
  • Programmer. Older two-channel programmers can lose one channel. Check both heating and hot water are set to on, not timed, for a test.
  • Immersion heater as a stopgap. Most cylinders have an electric immersion heater. Switch it on at the wall and you will have hot water in about an hour while you wait for the engineer.
  • Airlock or pump. If the cylinder is hot but the taps upstairs run cold, there may be an airlock in the hot water pipework, and if nothing is circulating the pump may have seized.

What we do when we come out

A boiler repair visit starts from £90. The engineer tests the boiler, the valves and the controls, tells you exactly what has failed and what it costs to fix before touching anything, and carries diverter valves, motorised valve heads, thermostats and plate exchangers for the common makes on the van. If the cylinder itself has failed, we fit replacement cylinders from £550, and unvented cylinders that give you mains-pressure showers upstairs.

No hot water for a family is not something to live with for a week. Ring us, or send the form on this page and we will call you back.

Questions

Why is my hot water lukewarm but the heating is fine?

On a combi this usually means the plate heat exchanger is scaled up or the diverter valve is only partly moving. Both are repairs rather than replacements. In Essex hard water, a scale reducer fitted afterwards stops it coming back.

Can I fix a stuck diverter valve myself?

No. It sits inside the boiler casing, which only a Gas Safe registered engineer should open. What you can safely do is check the thermostat, the programmer and the pressure before you call, which rules out the simple causes.

How long does a diverter valve repair take?

About an hour once the engineer is there, and we carry the common valves for Baxi, Worcester Bosch, Vaillant and Ideal on the van, so most are done on the first visit.

Should I just replace the boiler?

Not for a single failed valve. If the boiler is over 12 years old and this is the third repair in two winters, it is worth the conversation, and we will give you both prices so you can decide.

Written by Essex Heating Engineers Ltd, Gas Safe registered 925538, Basildon. Prices quoted are our own published starting prices and are checked when this page is updated.

More guides

Need a heating engineer or plumber today?

Family-run, Gas Safe registered and based in Basildon. Call us, message us on WhatsApp, or send a quote request and we will ring you back.

Emergency line answered 24 hours

Call now WhatsApp

Leave your number and we will ring you

When suits you?

We only use your number to call you about this. No mailing lists, no sales calls.

    ↑↓ to moveEnter to openEsc to close

    Web Design By UKBox
    UKBox Logo

    Close Button

    Web Design By UKBOX