Maldon is around 25 minutes from Bowers Gifford, so a leaking cylinder does not have to wait long. The very hard water across the Maldon area, 360 ppm on average, is the main reason cylinders and immersion elements here fail early, and we fit scale protection with every replacement. Around 76% of Maldon homes heat their water with gas.
A hot water cylinder stores the water heated by your boiler or immersion heater, and in a vented system a cold water tank in the loft feeds it. Cylinders scale up, corrode and eventually leak, loft tanks crack or grow contaminated, immersion elements burn out and the valves around them fail. We replace all of it across Essex.
We check whether a like-for-like replacement is right or whether the property would be better served by a different cylinder or by a combi boiler, then quote. On the day we drain and remove the old cylinder or tank, fit the new one with its thermostat, valves and insulation, refill, check for leaks and test the hot water at every outlet.
Essex water is hard to very hard, which is why cylinders and immersion elements here fail sooner than they should. We can fit a scale reducer or softener on the cold feed at the same time. Water tank installation starts from £550 and cylinder work is quoted after we have seen the airing cupboard. Gas Safe registered (925538).
- Drive from base
- 17.4 miaround 25 minutes
- Homes on mains gas
- 76%2021 Census
- Water hardness
- 360 ppmVery hard water
- Hot Water Cylinders
- From £550Price agreed first
Hot Water Cylinders and Tanks in Maldon: the local picture
76% of the 6,692 households around Maldon heat with mains gas only, 10% are electric only and 2.8% run on oil (2021 Census, ward level).
Water in the Maldon area is very hard at around 360 ppm, so limescale in boilers, cylinders and showers is a common cause of faults here.
Maldon is 17.4 miles from our base in Bowers Gifford, around 25 minutes by van.
What is included
- Hot water cylinder replacement
- Cold water storage tank replacement in the loft
- Immersion heater and element replacement
- Cylinder thermostats and motorised valves
- Expansion vessels and pressure relief valves
- Scale reducer or softener on the cold feed
- Insulation jackets and pipe lagging
- Removal and disposal of the old cylinder or tank
How it works
- Inspect the cylinder, tank and airing cupboard
- Quote for the replacement and any valves or controls
- Drain down and remove the old unit
- Fit the new cylinder or tank, valves and insulation
- Refill, check for leaks and test every hot tap
Recent work
What Maldon customers say
Joshua FoxGoogle review★★★★★Essex Heating Engineers installed a new boiler for me in Rayleigh, and they were excellent from start to finish. The team was punctual, tidy, and really professional. The installation was quick, everything was explained clearly, and the new boiler works per...
Darren DeaconGoogle review★★★★★Ash arrived on time, gave us his advice and explained how we should proceed. His quote was reasonable and when we get his email we will arrange a time for the installation of a new thermostat. They covered our floors, so they didn't track anything in. They ...
Jack CoreyGoogle review★★★★★Essex Heating Engineers is my go-to company. They always do a great job. Dean was especially knowledgeable, efficient and dedicated. Getting my house back in working order after a leak in the upstairs bath was problematical, to say the least. But Dean did w...
Questions about hot water cylinders and tanks in Maldon
How much does a new hot water cylinder or tank cost?
Water tank installation starts from £550. A hot water cylinder is quoted after we have seen the existing one, because the price depends on its size, type and how much of the surrounding pipework and valves need replacing. Immersion element replacement is a fixed-price plumbing job from £90.
How quickly can you replace a leaking cylinder?
A leaking cylinder is treated as urgent. Call 01268 855605, and if the leak is bad the engineer will talk you through isolating it while we arrange the visit. Cylinders are usually available quickly from local suppliers, and the engineer will give you a date when the quote is agreed.
How do I know my cylinder needs replacing?
Signs include water on the airing cupboard floor, rust streaks on the cylinder, hot water that runs out faster than it used to, and an immersion heater that has needed more than one new element. A cylinder that has been on very hard water for many years may be full of scale even if it is not leaking.
Should I replace the cylinder or switch to a combi?
If the house has one bathroom and good mains pressure, a combi from £1,980 fitted removes the cylinder, the loft tank and the airing cupboard clutter. If two showers run at the same time, a cylinder still does the job better. We look at the house and give you a price for both.
How far is Maldon from you?
Maldon is 17.4 miles from our base in Bowers Gifford, around 25 minutes by van. Next-day appointments for repairs and installs, and emergencies as availability allows. Typical drive time around 25 minutes.
Other services in Maldon
- Boiler Installation and Replacement
- Central Heating Installation
- Central Heating Repairs
- Radiators and Radiator Valves
- Smart Thermostats and Heating Controls
- Underfloor Heating
- Plumbing Repairs and Leak Detection
- Water Softeners and Limescale Protection
- All services in Maldon
Hot Water Cylinders and Tanks near Maldon
See the full Hot Water Cylinders and Tanks page for everything we cover across Essex.
